How long does a typical heating repair take?

Most repairs take one to three hours, depending on the part and how easy it is to reach. A simple flame sensor cleaning might take 45 minutes, while replacing a blower motor in a tight attic can take longer.

How can I tell if my furnace needs repair or replacement?

If the furnace is more than 15 years old, has a cracked heat exchanger, or needs frequent repairs, replacement may be more cost-effective. A single repair is usually worth it if the unit is younger and the fix is straightforward.

Will bad weather delay my heating repair?

Freezing rain, ice, or deep snow can slow down outdoor work on heat pumps or high-efficiency furnace vents. We still come out, but we may need extra time to clear access or work safely in slippery conditions.

What mess or debris will be left behind after the repair?

We lay drop cloths and vacuum the burner area and surrounding floor. You may see a small amount of dust from the old part, but we clean up fully before leaving. No debris is left behind.

How do you estimate the cost of a heating repair?

We give a flat-rate price for the diagnosis visit. After we find the problem, we quote the part and labor cost before any work begins. You approve the price in writing before we proceed with the repair.

What should I do before the repair crew arrives?

Clear a path to the furnace or heat pump, remove any stored items or boxes near the unit, and make sure pets are secured. If you have a gas shutoff valve, let us know where it is located.

SSan Marcos HVAC Experts

(512) 201-1041 Get Free Estimate

San Marcos HVAC Experts

Heating Repair

Name: San Marcos HVAC Experts
Address: San Marcos, TX
Telephone: +15122011041
Rating: 4.9

Heating Repair in San Marcos, TX. Free, no-pressure estimates.

4.9 stars on Google

From 28 verified customer reviews.

Local, and close by

Covering San Marcos, TX & the surrounding area.

Free estimates

Tell us what needs doing and we will come out and take a look.

The work

About our heating repair

When the temperature drops and your furnace stops producing heat, you are facing more than just discomfort. A failed heating system can freeze pipes and make your home unsafe. You call because the house is cold, the system is not responding, or it is blowing air that never warms up. This is an urgent situation that needs a prompt visit from a technician who understands gas and electric heating systems.

Our crew arrives with a full set of diagnostic tools: multimeters, manometers for gas pressure, combustion analyzers, and a selection of ignitors, flame sensors, thermocouples, capacitors, and blower motors. We start by checking power and gas supply, then test the thermostat, safety switches, and sequence of operation. We clean the flame sensor, inspect the heat exchanger for cracks, and verify venting before we replace any part.

The time and cost of a heating repair depend on the system type, its age, and how hard it is to reach the failed component. A gas furnace in a tight attic or crawlspace takes longer to access than a unit in a basement. Older systems may have corroded wiring or seized blower wheels that add labor. Weather conditions like freezing rain can slow down outdoor work on heat pumps or boiler exhausts.

On the day of the repair, we lay down drop cloths to protect flooring and move furniture only as needed. We work cleanly, vacuum dust from the burner compartment, and test the system through a full cycle. After we finish, we explain what was wrong, show you the part we replaced, and walk you through how to set the thermostat. You do not need to do anything beforehand except clear a path to the equipment.

Flame Sensor Cleaning

A dirty flame sensor is a common cause of a furnace that lights then shuts off. We sand it with fine grit to restore reliable operation.

Heat Exchanger Crack

A cracked heat exchanger can leak carbon monoxide into your home. We inspect every seam with a mirror and a combustion analyzer.

How we work

Same crew from quote to clean-up
We show up when we say we will
No surprises on the final bill
We explain what we find in plain English
Every job gets a full system check
We clean up like we were never there

San Marcos HVAC Experts

Get a Free Quote

How the job runs

Our 4-step heating repair process

Diagnose the Problem

We check thermostat, power, gas supply, and safety switches. Then we run the system through its cycle to identify the exact failure point.

Secure the System

We shut off gas and power, lock out the disconnect, and confirm zero voltage before touching any electrical components.

Replace or Repair

We remove the faulty part, install the correct replacement, and reconnect all wiring and gas lines. We test for leaks and proper operation.

Test and Verify

We run the system through a full heat cycle, check temperature rise, measure gas pressure, and confirm safety controls function before leaving.

The difference

Why San Marcos HVAC Experts for heating repair

Heat Exchanger Safety
A cracked heat exchanger can leak carbon monoxide into your living space. We inspect every unit with a combustion analyzer to catch hidden failures before they become dangerous.
Correct Diagnosis First
Throwing parts at a heating problem wastes time and money. We test each component in sequence to find the real cause, so you only pay for what actually fixes the system.
Clean Work Habits
Heating repairs create dust and debris. We lay drop cloths, vacuum the burner compartment, and leave the area cleaner than we found it so you can use your heat right away.